The Gavita Master controllers (in combination with suitable Gavita e-series fixtures) offer a solution for all these issues, even with a cost reduction when you look at larger climate rooms. The E-series ballasts no longer require a switchboard to be switched on and off, and no longer need their own switch to dim or boost them. Now you can just touch a few buttons on your controller to be in complete control of all your connected ballasts at once. Our Master controllers do this, and much more!
Dimmable electronic ballasts have been around for many years now. They offer flexibility when you need lower light intensities, for example during the vegetative phase or when climate conditions are so extreme that a healthy climate is hard to maintain. Moreover they can be boosted to optimise lamp performance and efficancy. Unfortunately it is not always easy to adjust multiple ballasts, or be there at the right moment when you need to dim your lights. Another problem is the high current that ballasts require when switched on at the same time (the inrush current). You need elaborate contactor equipped switchboxes to switch your ballasts on and off.
Functionality overview - Easy installation
Installing the Master Controller is a breeze: it’s a matter of plugging in, setting the dials of the ballasts to EXT (External control) and looping the low voltage control cord from the controller to your ballasts - all plug and play. Easy, safe and flexible.
The five language interface is intuitive to use with just 5 buttons. In plain text you see all settings, warnings and statuses. For an easy overview we have added LEDs for each output channel, which indicate whether the lights are on, dimming or shut down due to a dangerous high temperature. The indication LEDs are supported by a full text warning on the high quality green OLED display.
Replaces timers and contactors
You can plug your ballasts directly into mains outlets. You do not need any timers or contactor boxes any more: the ballasts are in stand-by mode and wake up when they get the signal from the controller. This means that you don’t have any inrush any more when you switch on your ballasts. Just set the on/off time on the controller and you are good to go.
The EL2 controller offers you a main and an auxiliary channel which follow each other or work alternating. The latter is specifically for when you want to optimise your power utilization in the generative phase, running 2 rooms with the light alternating every 12 hours in two climate rooms. Easy and flexible.
Dimming and boosting
Once you have connected your ballasts to the controller and set the on/off time you can set the output power centrally by the push of a few buttons. You can choose to have the output power displayed as a percentage or in actual output wattage of your ballasts. We even offer you a sunrise/ sunset time setting in which the lamps ramp up or down at the start and end of the cycle.
Autodim and safety shutdown based on room temperature
The Master controller is equipped with temperature sensors. Though we do not intend for you to use the Master controller as a climate controller, it can help you save your crop when temperatures in your room rise beyond your climate control capabilities. At a set temperature (normally a few degrees above your set ideal climate temperature) the Master controller will automatically dim your lamps, to prevent crop damage. In case of a complete ventilation failure or other calamity, when temperatures rise even more, the Master controller shuts down all connected equipment and activates the alarm contact.
Switching auxiliary equipment
The Master controller has two outputs for optional External Contactor Modules (ECMs). These industry grade contactor units can switch a load up to 15 amps of accessories during either lights on or lights off period. Using the ECMs you can switch, for example, your humidifier, heating, CO2 equipment and watering systems. As the ECMs are steered by a low voltage signal you can even locate them close to the accessories themselves, enabling easy installation and optimal flexibility.
The Gavita EL controller series currently comprises of two models: The EL1 and EL2. Both feature auto-dim, auto-shutdown, sunrise/sunset and timer. The EL1 has one output channel, while the EL2 has 2 output channels and additional outputs for External Contactor Modules and alarm contacts. For one room without auxiliary equipment or alarm contacts, the EL1 is the best choice for you. If you require switched auxiliary equipment during lights on / off, alarm contacts and/or a 2 room 12/12 setup, the EL2 is most suitable.